BOUNCE
SPRAY-ON
RUBBER COATING

DESCRIPTION
BOUNCE SPRAY-ON RUBBER COATING is a clear elastomeric coating for use in the electrical and electronic industries. Bounce forms an impervious coating on all electrical contacts, circuit boards, electrical panels to protect against rust and corrosion. High dielectic 4 mil coating provides 300 volt dielectric. Waterproof, flexible and permanent. Works even when totally submerged in water. Dries to a clear transparent coating.

APPLICATIONS
For use in industrial, construction, HVAC, RV, marine, electrical contracting and electronic applications. Use on electrical connections. phone and cable circuits, electrical systems, motor connections, circuit boards, outdoor lighting, security systems, electrical panels. general waterproofing.

FEATURES & BENEFITS
Dries quickly -Easy to apply- Prevents rust and corrosion-
High dielectric- Conformal coating, flexible, transparent

SPECIFICATIONS
FORM:                                             Solvent Based Aerosol
ODOR:                                             Moderate Solvent
COLOR:                                          Clear
DETERGENCY:                             N/A
TOXICITY:                                       100 ppm OSHA PEL 
WETTING ABILITY:                        N/A
PHOSPHATES:                             N/A
STORAGE STABILITY:                 1 year + COLD STABILITY: 32°F

LABEL INFORMATION
FLASH POINT:                               >100"1
FLAME EXTENSION:                   <18"
SOLUBILITY IN WATER:               N/A
SPECIFIC GRAVITY:                     0.77
% VOLATilE BY VOLUME:           N/A
EVAPORATION RATE:                 Medium Fast
BIODEGRADABLE:                      N/A
PROPELLANT:                              Hydrocarbon
pH:                                                   N/A

BOUNCE is a clear rubber based conformal coating. Designed for protection of electrical connections and general waterproofing. Use on circuit boards, electrical wiring and panels, coaxial cable connections, phone circuitry, pool equipment, outdoor lighting, security systems, junction boxes. Waterproofs all types of electrical connections preventing rust, corrosion. signal loss, loose connections, power loss. Provides up to 300 volts dielectric with a 4 mil coating. Thicker coats will provide improved dielectric protection. Dries clear so connections are still visible for inspection. Conforms to surfaces coated to provide a complete seal.
For use in industrial plants, building maintenance, HVAC service and repair, marine, RV, pool maintenance, outdoor lighting, phone and cable installation and maintenance, motors. Also use for general waterproofing of surfaces and equipment.
For indoor or enclosed use, not suitable for long term outdoor use with direct exposure to sunlight.

DIRECTIONS FOR USE: Remove cap. Shake can well for 30 seconds. Clean and dry surface prior to application. Hold can 6 to 8 inches away from surface to be coated. Apply in short even strokes until thoroughly coated. Allow surface to dry for 15 minutes before use. Additional applications can be made to provide additional dielectric rating. Cleanup with paint thinner or mineral spirits. After use. can should be turned upside down and sprayed to remove material from spray tip before storing. This will keep tip free of buildup.
DO NOT APPLY TO ENERGIZED EQUIPMENT OR LIVE HIGH VOLTAGE CONNECTIONS.
CAUTION: Extremely Flammable. Contents under pressure. Keep out of the reach of children. Vapor Harmful. Avoid breathing of vapors or mist. Avoid contact with skin and eyes. Do not apply to energized equipment. Do not use near fire, sparks or open flame. Do not puncture or incinerate container. Exposure to temperatures above 120°F may cause bursting.
WARNING: This product contains chemical(s) known to the State of California to cause cancer.
CONTAINS (CAS#): Hydrocarbon Propellent (68476-86-8), Xylene (1330-20-7), Aromatic Hydrocarbon (108-88-3), Aliphatic Hydrocarbon (110-54-3). Poly butadiene-co-styrene (9003-55-8).
PACKAGING INFORMATION  16 oz cans  11 oz net weight.